Rubber Stall mat at Tractor Supply. Any good for a garage floor?
2009年8月27日 · I was at Tractor supply today and I seen rubber mat they make for horse stalls. I was just curious if anyone ever used it on a garage floor. It would give you some cushion plus possibly protect a precision tool from being trash if ever dropped. They are 4'x6' sheets for …
General | Cutting 6" diameter hole in 3/4" rubber mat | Practical ...
2022年8月15日 · I want to put a horse stall mat under and in front of my lathe. To go under I need to cut two six inch diameter holes for the lathe feet pads. I was thinking hole saw or jig saw. Mat is too big and heavy to use a flycutter in the drillpress. I cut straight cuts with a razor knife but curves that tight would be hard to do. What about a grit edge ...
Where do I find a flat belt - Practical Machinist
2007年5月20日 · The McMaster stuff is cheaper, except I need to pay $$$ shipping. Tractor Supply is local, but limited widths need cutting. I have used baler belt it has a nice sticky black rubber surface. What is the deal with "tan" color SBR belt. Is that a woven matterial cover? Does it provide a good grip. The Tractor supply is only two ply, but seems very ...
Suggest Steel for antique tractor flywheel performance
2020年1月5日 · AS your tractor pulls and no-load speed drops slightly under the load, and the governor slowly opens the throttle, hp output is rising to carry the increasing load. Once the rpm has dropped enough for the governor to hold the throttle full open, and load still increases and engine begins to lug down, you are using the steady-state hp the engine ...
repainting a machine with currently available paint - Practical …
2024年11月3日 · I used the Tractor Supply blue paint in a Monarch lathe about 16 years ago. It was brushed on, and still there. The oil and solvents haven't affected it. It doesn't chip when hit. It's not shiny like a car, but it does have some gloss . I've used the brown and black for outdoor fencing and it stays on .
General | Anti-fatigue mats | Practical Machinist - Largest ...
2011年8月21日 · Those mats don't do jack. Biggest help will be fixing your own body. Lose weight, exercise, diet, physically therapy/personal trainer. Can't blame the floor when you may have a big beer belly screwing up your back. If you want to feel better you have to …
OT - sizing a hydraulic cylinder for log splitting - Practical Machinist
2006年1月24日 · My 22 ton TSC splitter has a 4" cylinder with a 1 1/2" rod, 2 stage pump, 11 gpm, I've never been able to stall it and I've tried. Last time using showed my GD how powerful it is I put a 5" oak branch cross ways and split it, had to do it in 2 passes because the wedge doesn't get with in 2" of the foot (it must be a government thing) for a ...
General | Solvent for Parts Washer - Practical Machinist
2018年10月24日 · Couple months ago, I went 'round with this and decided to dump 3 gallons of diesel fuel in the parts washer rather than pay 2x the price for paint thinner. It works OK, but it does leave a bit more greasy residue than I care for. The PSC 1000 from Tractor supply at $9/ gallon seems to be the best deal out there for 'real' parts washer solvent.
Static phase converter - Practical Machinist
2024年10月31日 · Air compressors are the exact opposite. They start up with a heavy load trying to spin that pump, and the heavy load is continuous. The load is designed to use everything the motor has for torque. Except: you won't have everything the motor should be putting out and it …
WTB: Craftsman/King-Seeley dp motor pulley - Practical Machinist
2010年12月7日 · I was just given one of these presses, and it has a single-groove pulley on the motor instead of the original 4-step. The part number for the 4-step was 38390, and is NLA from Sears. I know there are a bunch of these old "150" presses hanging out in the back of people's shops - anybody want to...